[TANAKA]KV-6運動粘度恒溫槽 運動粘度

運動粘度測試恒溫槽

KV-6

Optional Six-Channel Quartz Timer

加配多路計時器

 

The model KV-6 is a Constant Temperature Bath designed for measurement of kinematic viscosity of liquid petroleum products.

KV-6 多路計時器是運動粘度測試恒溫槽是配合液體石油產品運動粘度的測試方法（動態粘度所使用的專用恒溫浴槽，能夠提供正確的測試溫度和（zui高）±0.01℃高精度恒溫環境。

A fluorescent lamp illuminates viscometers brightly for easy observation of meniscus. 儀器本體前側上方熒光照明，浴槽視場清晰，可清晰觀察試樣的彎月面。

Seven viscometer holders (for Cannon-Fenske or Ubbelohde viscometers) are included as standard accessories. (Viscometers, bath liquid and liquid-in-glass thermometers must be purchased separately.) 儀器可同時安裝7組粘度計進行試驗，隨機可提供對應的（坎氏/烏氏）粘度計安支架（請看后文的訂購說明。運動粘度計，和配套的溫度計并不提供，需要另行購買）

WIDE TEMPERATURE RANGE (20℃ to 150℃) AND HIGH ACCURACY TEMPERATURE CONTROL 可提供從(20℃ - 150℃)的溫度控制范圍和高精度的恒溫環境

KV-6 maintains bath liquid temperature accurately as required by ASTM D445.

KV-6運動粘度測試恒溫槽可提供嚴格按照ASTM D445的試驗方法要求的溫度環境。

Within the range of 20 ℃ to 100 ℃, the temperature is controlled within +/-0.01 ℃; +/-0.03 ℃for outside of this range.

控溫精度：20℃-100℃時，+/-0.01 ℃ 超過20℃-100℃范圍以外的，+/-0.03 ℃

For 20 ℃ to 30 ℃, connect the built-in cooling pipe to tap water or a recirculating water chiller.

20℃-30℃時，儀器需要配合外接循環制冷源使用。

DIGITAL TEMPERATURE DISPLAY 數字顯示

Microprocessor and built-in platinum resistance probe (PT-100) allows one-touch temperature selection and on-screen temperature display.

儀器內置高速微處理器，配合PT-100（鉑電阻），數字顯示浴槽溫度。

溫度選擇可單鍵操作，預置定點溫度，使用簡單，性能可靠。

TANAKA Kinematic Viscosity Bath, model KV-6

SPECIFICATIONS:

CONFORMING STANDARDS: 適用標準

ASTM D445, GB/T 265， ISO 3104, IP71 and JIS K2288

APPLICABLE VISCOMETER:

Cannon-Fenske type, 坎農-芬斯克毛細管粘度計，芬氏粘度計

Cannon-Fenske Reverse flow type (with standard viscometer holder),

芬氏逆流粘度計（可通用標準附件中的粘度計支架）

Ubbelohde type (with optional viscometer holder) 烏氏粘度計（注意：需要定購的粘度計支架）

特別說明：SH/T173-92(2004)《玻璃毛細管粘度計技術條件》，BMN-1，BMN-2型對應使用的是品氏粘度計，需要訂購配套的粘度計支架。BMN-3對應的是芬氏粘度計，BMN-4型對應的是芬氏逆流粘度計，可使用標準附件的粘度計支架

BATH:

Stainless Steel with a heat resistant glass, W320 x D230 x H320 mm

Equipped with overflow tube and drain cock Capacity: 23 liters

鋼化耐熱方桶形玻璃浴槽，W320×D230×H330(mm)

有防溢口和排液閥的設計，容積 23升

TEMPERATURE CONTROL: 溫度控制

PID controlled by Microprocessor Precision : ± 0.01℃ @ 20 ℃ to 100 ℃ ± 0.03℃ outside of above range 高速微處理器，PID控溫，控溫精度：20℃-100℃時，+/-0.01 ℃ 超過20℃-100℃范圍以外的，+/-0.03 ℃

Preset temp. : six temperature points: 25, 40, 50, 80, 100 and 135 ℃. Preset temperature can be changed at the factory at any point between 20 to 150 ℃. (optional) Please specify when ordering.

標準型為20、40、50、80、100℃、135℃ 預置6點隨意切換（特殊溫度點可在20-150℃范圍內選定，需在工廠內定制，訂購前必須聲明）

Temp. Adjust : by pressing switches located at the front panel. 前面板溫度選擇按鍵

Temp. Sensor: PT-100 傳感器

HEATER: 加熱功率

Sheathed Heaters, 700W x 2 pcs 電加熱絲，700W x 2

COOLING SYSTEM:

For 20 to 30 ℃, by flowing a cooling medium through the cooling pipe installed at the bottom of bath. (Provision for cooling medium is optional) 推薦：20℃-30℃時，儀器需要配合外接循環制冷源使用。

STIRRER: 

Propeller type. Highly efficient heat exchange is established. 內置高效的攪拌循環，均勻控溫

ILLUMINATION:

A fluorescent light positioned horizontally in the front-top of the bath.

儀器本體前側上方水平安置熒光照明，浴槽視場清晰。

RECOMMENDED BATH MEDIUM 推薦水浴介質

20 to 80 ℃: Distilled Water Above 80 ℃: Silicone Oil

20 -80℃: 可使用蒸餾水： 80℃以上:高溫透明硅油（加熱不變色）

DIMENSIONS AND WEIGHT:  （體積/重量）

W400 x D380 x H662 mm, 33kg (56kg with water filled) 注水后約5656

POWER REQUIREMENTS: 電源需求

100 or 120VAC, 15A Max.

220 or 240VAC, 9A Max.

 Please specify when ordering. （訂購前請事先說明）

ORDERING INFORMATION: 

STANDARD ACCESSORIES: （標準附件）

1.    Viscometer Holder, for Cannon-Fenske type*芬氏粘度計支架	7 pcs
2.    Lid for Viscometer Holder Openning 浴槽蓋	7 pcs
3.    Temperature Sensor 溫度傳感器	1 pc
4.    Silicon Stopper No.0A for Thermometer 硅膠塞，安裝溫度計用	1 pc

*: It can be replaced with Ubbelohde type upon request. 可改換為同數量的烏氏粘度計支架

Please specify when ordering. （訂購前請事先說明）

OPTIONAL ACCESSORIES: （選購件1）

Viscometer Tube Holder for Ubbelohde type烏氏粘度計支架

Viscometer Tube, Cannon-Fenske Routine type 芬氏粘度計（常用，透明）

Viscometer Tube, Cannon-Fenske Opaque type 芬氏粘度計（不透明）

Viscometer Tube, Ubbelohde type烏氏粘度計

Silicone Bath Oil (SRX-310), 20 kg 高溫硅油(SRX-310)，20公斤裝

Six-Channel Quartz Timer, Model: DSW-6 多路計時器DSW-6（日本田中制）

ASTM標準溫度計：

Thermometer ASTM 28C (37.8℃)

Thermometer ASTM 29C (54.4 ℃)

Thermometer ASTM 40C (80.0 ℃)

Thermometer ASTM 44C (20.0 ℃)

Thermometer ASTM 45C (25.0 ℃)

Thermometer ASTM 46C (50.0 ℃)

Thermometer ASTM 47C (60.0 ℃)

Thermometer ASTM 110C (135.0 ℃)

Thermometer ASTM 118C (30.0 ℃)

Thermometer ASTM 120C (40.0 ℃)

Thermometer ASTM 121C (100.0 ℃)

Thermometer ASTM 129C (93.3 ℃)

Thermometer ASTM 132C (150.0 ℃)

SUGGESTED SPARES FOR 2 YEARS: （選購件2，2年維護用）

1.    Fluorescent Light 6W 2 pcs 照明熒光燈 6w, 2

2.    Glow Lamp 1 pc 指示燈，1